Improve the safety of your equipment with the xTool Fire Safety Set 2. This automatic CO₂ fire suppression system communicates with the machine's flame sensor to activate in the event of a fire.
Its 600 ml cartridge supports multiple activations and includes a gas level monitoring system.
Our experts are at your service to answer your questions and provide advice at info@polyfab3d.com.
Delivery within 48/72 hours
Order before 1pm. Same day shipping
Free delivery
Free delivery near you from €69.90
Premium support
Our teams are on hand to answer all your questions
Over 3500 products
A wide choice of products from the biggest brands
The xTool Fire Safety Set 2 is a fire protection device designed to improve the safety of laser engraving and cutting equipment. Connected to the machine, it communicates with its flame detection sensor to automatically release CO₂ if a fire breaks out.
This second-generation system features a 600 ml cartridge, manual activation and gas level monitoring. With several possible suppression cycles, it provides additional protection for users looking to secure their working environment.
Compatible with: xTool X1, xTool M2, xTool F2 Ultra, xTool F2 Ultra UV, xTool F1 Ultra.
The Fire Safety Set 2 communicates directly with the machine's detection system. When the flame sensor built into the laser engraver detects a fire, it sends a signal to the device, which automatically releases CO₂.
Fire suppression is activated in less than one second after the signal is received. This automated response helps act quickly to limit the spread of a fire within the working area.
The xTool Fire Safety Set 2 features a 600 ml CO₂ cartridge, compared with 48 ml for the first generation. It contains approximately 400 g of gas and supports several fire suppression cycles before it needs replacing.
For the xTool X1, xTool specifies approximately 2 to 3 activations per cartridge. This increased capacity allows the system to be reset after activation, leaving a reserve for further interventions.
In addition to its automatic operation, the Fire Safety Set 2 features a manual activation control. This allows users to activate the system directly whenever intervention is required. It provides an additional safety measure by offering an activation method independent of automatic detection.
Combined with communication with the machine and its CO₂ supply, this function completes the fire protection system designed for compatible xTool equipment.
Unlike the first generation, the Fire Safety Set 2 includes a gas level monitoring system. This feature checks the amount of CO₂ available in the cartridge and provides an indication of the remaining fire suppression supply. The system also monitors the mechanism's operation, including potential motor blockages and status indicators. This information makes it easier to keep track of the device and anticipate maintenance requirements or cartridge replacement.
The Fire Safety Set 2 is designed to support multiple discharge cycles. After each activation, the system can be reset and made available for another intervention, depending on the amount of CO₂ remaining in the cartridge. This is a significant improvement over the first version, which only supported a single activation. The number of uses nevertheless depends on the connected machine: xTool specifies 2 to 3 discharges for the X1 with a full cartridge.
The device works in conjunction with the flame detection sensor built into the machine. This communication automates activation without requiring immediate user intervention when a flame is detected. The Fire Safety Set 2 therefore complements the laser engraver's safety features by adding an active CO₂ fire suppression function. However, it should be considered an additional safety measure and does not replace machine supervision during operation or standard safety precautions.
The xTool Fire Safety Set 2 offers a worthwhile improvement in laser engraving safety. Its 600 ml cartridge, automatic activation and CO₂ level monitoring make it more comprehensive than the first generation.
The ability to perform several fire suppression cycles is another valuable advantage, particularly for users who operate their equipment regularly. A useful safety accessory to complement an xTool setup, provided that operating instructions are followed and appropriate supervision is maintained during laser operations.
Specifications for xTool Fire Safety Set 2, xTool X1, M2, F1 Ultra, F2 Ultra, F2 Ultra UV
Technology / Product
Spare part
Aucun avis ne correspond à votre recherche.
Aucune question publiée pour ce produit.
Vous ne trouvez pas la réponse à votre question ?